As of 2/23/0000.05 LIST OF CHANGES SINCE FIRST ISSUE
| 1.30 | "(Self contained meter socket)" was added to first sentence of fourth paragraph. |
| 4.20 | Information on Network service for PA was added to second page |
| 4.55 | Motor sizes were changed from 6.5 to 7.5 and 19.9 to 25hp (page1) |
| 8.05 | Added sentence at bottom of page to include other underground areas that should have services installed in the same manner as network services. |
| 8.15 | Information on network service for PA was removed and added to 4.20 |
| 9.05 | Information was added for Penelec and JCP&L as previous info was only Met-Ed |
| 12.12 | Min height on drawings 2&3 was changed from 15' to 12' |
| 12.76 | Reference under number #1 was changed from 13.15 to 13.40 |
| As of 03/08/00 |
|
| 4.15 | Changed minimum radius on conduit from 18" to 24". |
| 4.20 | Changed minimum radius on conduit from 18" to 24". |
| 4.25 | Added paragraph at end of three phase section which covers multiple services off transformer. |
| 4.50 | Changed dimensions for ct's in switchgear from 30" x 30"x 12" to 36" x 30" x 20". |
| 7.10 | Changed dimensions for ct's in switchgear from 30" x 30"x 12" to 36" x 30" x 20". |
| 12.14 | Changed minimum radius on conduit from 18" to 24". |
| 12.16 | Changed minimum radius on conduit from 18" to 24". |
| 12.28 | Changed minimum radius on conduit from 18" to 24". |
| 12.40 | Changed minimum radius on conduit from 18" to 24". |
| 12.42 | Changed minimum radius on conduit from 18" to 24". |
| 13.30 | Added Midwest to approved list for pedestals. |
| As
of 04/21/00 |
|
| 1.15 | Added definition of select fill and select bedding |
| 5.50 | Requirements about disconnects ahead of metering equipment changed. |
| 12.12 | Clearances changed, pipemast inf removed (refer to 12.10). |
| 13.02 | Murray and Siemens catalog #'s changed. |
| 13.04 | Midwest catalog #'s added. |
| 13.06 | Siemens catalog #'s changed. |
| 13.10 | Midwest catalog #'s added. |
| 13.12 | Thomas and Betts/Anchor, Cutler Hammer, Durham, Milbank, Siemens and Square D catalog #'s changed. |
| 13.14 | Siemens catalog #'s changed |
| 13.16 | Murray catalog #'s added and Siemens catalog #'s changed. |
| 13.22 | Siemens catalog #'s changed. |
| 13.26 | Midwest catalog #'s added. |
| 13.28 | Thomas and Betts/Anchor, Cutler Hammer, Durham, Milbank, Murray, Siemens and Square D catalog #'s changed. |
| 13.30 | Murray and Siemens catalog #'s changed. |
| 13.34 | Siemens catalog #'s changed |
| 13.36 | Thomas and Betts/Anchor, Cutler Hammer, Durham, Milbank, Siemens and Square D catalog #'s changed. |
| 13.38 | Siemens and Milbank catalog #'s changed. |
| 13.40 | Removed Lee Products |
| 13.42 | Murray catalog #'s added. |
| 13.44 | Murray catalog #'s added. |
| 13.60 | Requirements for 13.12, 13.28 and 13.36 now require anti-inversion kits or clips etc. |
| 14.05 | New requirement - Met-Ed inspectors list |
| 14.10 | New requirement - Penelec inspectors list |
| 15.05 | New requirement - Territory map |
| 16.05 | New requirement - Order form |
| As of 05/31/00 |
|
| 00.00 | Added 12.73 and 12.77 |
| 2.10 | Changed time required for previously served building inspection from 6 months to twelve months |
| 4.10 | Added clearance notes for swimming pools |
| 4.25 | Changed information on CT's |
| 5.50 | Changed disconnect information |
| 7.05 | Added reference to 12.73 & 12.77. Max CT cabinet now allowed is 2400A, larger than this requires ct's to be mounted in switchgear |
| 12.06 | Added fourth wire to drawing |
| 12.10 | Added Note 4 on grounding |
| 12.12 | Added clearance notes on drawing 2 and 3 |
| 12.14 | Added Note 4 on grounding |
| 12.16 | Added Note 3 on grounding |
| 12.18 | Changed Note 7 reference from 12.04 to 12.14 |
| 12.26 | Added Note 4 on grounding |
| 12.28 | Added Note 4 on grounding |
| 12.30 | Added Note 6 on grounding |
| 12.32 | Added Note 3 on grounding |
| 12.38 | Changed notes on drawing |
| 12.52 | Added PA requirements |
| 12.70 | Moved Note 5 to top phase |
| 12.73 | New Requirement |
| 12.76 | Changed Note 4, added Note 11 |
| 12.77 | New Requirement |
| 12.78 | Changed Note 7 |
| 13.40 | Added 1000A, 1200A, 1600A and 2400A CT cabinets |
| 13.60 | Changed note on 13.24 and 13.26 to refer to 13.22 not 13.20 |
| As of 09/08/00 |
|
| 4.15 | Added conduit information |
| 4.20 | Added conduit information |
| 4.25 | Added conduit information, added information from Requirement 4.50 revised disconnect requirements |
| 4.50 | Made Requirement obsolete (see requirement 4.25) |
| 5.10 | Changed meter socket location information |
| 5.50 | Added reference to other requirements |
| 12.04 | Changed attachment note |
| 12.06 | Changed attachment note |
| 12.08 | Changed attachment note and diagram |
| 12.18 | Changed notes on conduit |
| 12.22 | Added setting depth info |
| 12.26 | Changed attachment note |
| 12.52 | Changed dimensions for PA and NJ |
| 13.28 | Milbank does not accept 4", old inventory to be used up, only accepts up to 3" conduit, use other manufacturer or catalog # if 4" conduit is to be used |
| 13.16 | Changed Landis and Gyr catalog numbers |
| 13.40 | Added Milbank catalog number |
| 13.42 | Added GE catalog numbers |
| 13.44 | Added GE catalog numbers |
| 13.46 | Added GE catalog numbers |
| 13.48 | Added GE catalog numbers |
| 13.50 | Added GE catalog numbers |
| 13.60 | Added requirements for 13.40 (800A-2400A CT cabinets) |
| 14.05 | Inspectors List updated |
| 14.10 | Inspectors List updated |
| 17.05 | New Requirement |
| As of 04/27/01 |
|
| 13.40 | Added "Meter Devices Company, Inc." to approved list for 400-800A C.T. cabinets |
| As of 06/18/01 |
|
| 13.04 | Added Cutler-Hammer catalog number |
| 13.08 | Added Cutler-Hammer catalog number |
| 13.10 | Added Cutler-Hammer catalog number |
| 13.24 | Added Cutler-Hammer catalog number |
| 13.26 | Added Cutler-Hammer catalog number |
End of Specification:
Created: |
09/14/2000 | |
Last Revised: |
06/18/2001 |
